| Aprilia Tuareg 660 |
2022 |
1 1/8" |
Yes cables all work, No issue with cable/hose/wire lengths. Just have to loosen up some of the OEM straps |
1.5" Barback Style
3R-B17R |
- |
- |
- |
| BMW F650GS (Twin) |
2009 & Newer |
7/8" |
no, needs brake line, a +2 inch brake line can be purchased from Spiegler Performance |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| BMW F650GS (Single) |
up to 2007 |
7/8" |
Yes, see notes, Installing risers on this bike will require rerouting of the cables. This process will vary between bikes but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| BMW F700GS/F750GS |
All Years |
7/8" |
yes |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| BMW F800GS (Standard & Adventure Models) |
2008-2019 |
1 1/8" |
yes |
1 3/4" Anodized
3R-P2PPL |
1 3/4" Black
3R-P2PPLK |
- |
- |
| BMW F800GS (Standard & Adventure Models) |
2024 and Newer |
7/8" |
yes, Your OEM cap and GPS can mount to the top of these risers as well if your bike is equiped with a GPS |
1.25" Barback Block
3R-B12POE |
- |
- |
- |
| BMW F800GT |
All Years |
1 1/8" |
no, needs new cables, According to the information we have, the throttle cable and the brake line both need to be replaced in order to install 2" risers. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| BMW F800ST |
All Years |
7/8" |
Yes, see notes, According to customer feedback the stock cables are long enough to install our 2" risers without replacing anything, but rerouting is necessary. This process will vary between years but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. Be sure to double check cable length prior to purchasing risers. |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Anti-Vibe SE
1R-AV2SE |
| BMW F850GS/F900GS |
2019 - Newer |
1 1/8" |
Yes, see notes, The only risers that will allow you to remount the BMW GPS unit are model 3R-B17R. According to customer feedback the stock cables are long enough to install these risers without replacing anything, but rerouting may be necessary. This process will vary between years but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. We are still waiting to determine whether our pivoting risers will fit the F850GS without replacing cables. Be sure to double check cable length prior to purchasing risers. |
1.5" Barback Style
3R-B17R |
- |
- |
- |
| BMW G310GS |
2018-Newer |
7/8" |
Yes, see notes, Rox 2" risers work on this bike with minor cable rerouting. This process will vary between bikes but it is minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| BMW G650 |
2007-2010 |
7/8" |
Varies, see notes, Although we have limited feedback in regard to cable length on this bike we’ve been told the cables are long enough to accomodate any of our 2" pivoting risers on all X-Country bikes but only long enough to accomodate our 1 1/4" block offset risers on all X-Challenge bikes. Do you have other info that can help? Please call us at 218-326-1794 or email sales@roxspeedfx.com |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| BMW K1600B / K1600 Grand America (Black Trim ONLY!) |
2018 and Newer |
1 1/8" |
Yes, see notes, This bike may require you to reroute the cables. This process will vary between bikes but it is minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| BMW R1100GS/R1150GS |
All Years |
7/8" |
Yes, see notes, Installing risers on this bike will require rerouting of the cables. This process will vary between bikes but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| BMW R1200GS/R1250GS (Watercooled; Standard & Adventure Models) |
2013-2023 |
1 1/4" |
Yes, see notes, The WC BMW R1200GS can use any of our recommended risers without replacing any of the cables, however cable rerouting is recommended. You can find instructions for cable rerouting on the 2" Pivoting Riser page or you can call us at 218.326.1794 for more info. |
2" Pivoting
1R-P13R-2125 |
2" Anti-Vibe Pivoting
1R-AV2GSA |
1.5" Barback Style
3R-B15R |
1.5" Straight Style
3R-B13R |
| BMW R1200GS (Air/Oil Cooled; Standard & Adventure Models) |
2012 and Older |
1 1/8" |
Yes, see notes, This bike will require you to reroute the cables to behind the triple clamp. Place the bike on the center stand. Remove any zip ties and move the cables to outside of any metal clamps that may be present. Drop the fork tubes. Move the cables to behind the triple clamp. Raise fork tubes back up and then tighten everything down properly. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe (2008-2012 ONLY!)
1R-AV2PP |
| BMW R1200R |
2011-2014 |
1 1/8" |
TBD, see notes, In 2015 BMW changed the R1200R to a 1 1/4" handlebar and angled bar clamps. We have not had one of these bikes in our shop but as far as we know we don’t currently make a riser that will fit because of the bar clamp angle and the height of the OEM caps. Do you have info that could help? Click the contact button at the top of the page and drop us a note or call 218.326.1794. We don’t have any record of cable length on this bike. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| BMW R1200R |
2007-2010 |
7/8" |
TBD, see notes, Most bikes can use our 2" pivoting risers without replacing the stock cables, Most bikes can manage to install our 2" pivoting risers using all the stock cables, but we don’t have specific feedback on this bike. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| BMW R1100RT / R1150RT / R1200RT |
1996-2013 |
N/A |
No Risers Available |
Risers no longer available |
- |
- |
- |
| BMW R nineT |
All Years |
1 1/8" |
Yes, see notes, On some years, The OEM speedo on the R NineT will limit the rearward moving of our risers. Installing risers may require rerouting of the cables. This process will vary but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). Some customers have reported not needing to reroute cables on the nineT at all. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| BMW S1000R |
2013-Newer |
1 1/8" |
Yes, see notes, Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| BMW S1000XR |
2014-2019 |
1 1/4" |
TBD, see notes, We have very limited feedback in regard to which risers will work on the S1000XR. "We know that part 3R-B15R will fit year 2016 very well with no cable changes, cable re-routing still needed." From what we have been told installing other risers may require replacing the clutch cable and possibly others. Do you have info that can help? Call us at 218-326-1794 or email sales@roxspeedfx.com |
1.5" Barback Style
3R-B15R |
1.5" Straight Style
3R-B13R |
- |
- |
| BMW S1000XR |
2020 and newer |
1 1/8" |
Yes, see notes, According to customer feedback, our 1R-P2PP riser will fit with no cable changes, minor cable re-routing still needed." |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| BMW R1250RS (Only works on RS's with a traditional handlebar, not clip-on style bars) |
2023 & Newer |
1 1/8" or 1 1/4" |
See notes, According to customer feedback, Bikes with a traditional tubular bar, these risers will work. The stock cables will also work. Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it can involve: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
|
|
- |
- |
| BMW R1250RT (Only works on RT's with a traditional handlebar, not clip-on style bars) |
2022 |
1 1/4" |
See notes, According to customer feedback, These bikes have a 1 1/8" bar or a 1 1/4" bar. You need to call us so we can figure out what bar you have. the stock cables will work. Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it can involve: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
3R-B15R-15A |
|
- |
- |
| Buell Ulysses xB12x |
All Years |
7/8" |
yes |
2" Anodized
3R-P2SSM |
- |
- |
- |
| Can-Am Ryker & Ryker Rally |
2019 & Newer |
SPECIAL |
YES, see notes, The Ryker handlebar is a unique size. DO NOT use Rox Speed FX universal 7/8” pivoting risers (1R-P2SS, 1R-P2SE). Do not use any material, object or component as a shim or filler to fit, fix, attach or assemble a pivoting riser to any motor vehicle. Direct contact is required for proper assembly/fitment of Rox Pivoting Risers. Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Black
4R-P2RYK |
- |
- |
- |
| Can-Am Spyder F3 (will NOT work on RT or Limited models) |
2015 & Newer |
1 1/8" |
See notes, According to customer feedback, the stock cables will only work on the Spyder with the standard bar setup—the cables will NOT be long enough to work with the other “short reach” bar options. Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it can involve: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Can-Am Spyder RT |
2020 & Newer ONLY |
1 1/8" |
See notes, According to customer feedback, the stock cables will only work on the Spyder with the standard bar setup—the cables will NOT be long enough to work with the other “short reach” bar options. Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it can involve: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
Ducati Hypermotard |
All Years |
1 1/8" |
yes |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Ducati Monster 1100 / 1200 |
All Years |
1 1/8" |
Yes |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Ducati Monster 796 |
All Years |
1 1/8" |
NO See NotesAccording to customer feedback, the stock clutch cable and throttle cable doesn’t work with our riser. ROX Riser will fit with cable extensions. |
- |
- |
- |
- |
| Ducati Monster 659/797 |
2018-2021 |
7/8" |
yes, Acording to customer feedback. All cables and lines work with our 2 inch pivoting risers |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Ducati 821 |
All Years |
7/8" |
Yes |
2" Anodized
3R-P2SSM |
- |
- |
- |
| Ducati Multistrada |
2007 & Older |
7/8" |
yes |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Ducati Multistrada |
2008-2014 |
1 1/8" |
yes |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Ducati Multistrada 950/1200, Includes V4, V4 Pikes Peak and V4S |
2015 & Newer |
1 1/8" |
yes, see notesInstalling risers on this bike may require rerouting of the cables. This process will vary but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Ducati Desert X |
2022 & Newer |
1 1/8" |
YES, cables and lines work!,- see notes... We have not had one of these bikes in our shop to work on ourselves yet. We did have a customer try them and this is what he said. Cables are not an issue, This is what you need to do with the brake line. There are two cable holders attached to frame, one underneath headset and other on top of bike under gas tank. |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Ducati Scrambler Desert Sled |
|
UnKnown |
NO, see notes, At this time, we do not have a riser that fits this bike |
- |
- |
- |
- |
| Ducati Scrambler Sixty2 |
2016 |
7/8" |
yes, see notes, NOTES FROM CUSTOMER INSTALL - "The clutch cable, the brake and throttle had enough length but I did have to remove the headlight assembly and the plastic front tank panel to get at the wiring clips and ties to release them and give the extra length required for the control wiring. The left side, clutch micro switch and control switch wiring had less available slack. I did not have to remove the tank to get at the wire plugs to reroute the wires entirely… that saved a huge amount of work. There is enough slack in the wires now. The change in riding position is more upright and yet allows me to stand on the pegs for a little bit of “scrambling”. Thanks again for you assistance." |
2" Anodized
3R-P2SSM |
- |
- |
- |
| Ducati Streetfighter V4 |
All Years |
1-1/8" |
YES, see notes, Installing risers on this bike may require rerouting of the cables. This process will vary but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Ducati Urban Enduro |
All Years |
1 1/8" |
NO |
ROX Risers Do Not Work On This Bike! |
|
|
|
| Ducati XDiavel |
- |
UnKnown |
NO |
ROX Risers Do Not Work On This Bike! |
- |
- |
- |
| Harley Davidson 883L/883R/883N |
All Years |
1" |
unknown, Most bikes can manage to install our 2" pivoting risers using all the stock cables, but we don’t have specific feedback on this bike. If you have information that can help please give us a call at 218.326.1794 |
4" Black
4R-P4RX01 |
4" Aluminum
4R-P4RXM |
4" Chrome
4R-P4RX02 |
- |
| Harley Davidson FLSTF / FXDF / FXDLS / FXDWG |
2007 & Newer |
1 1/4" (double check bar size prior to order!) |
Yes, see notes, According to customer feedback, our 2" pivoting risers will work with stock cables on each of these bikes with some minor cable rerouting. |
2" Black
P13RIN |
- |
- |
- |
| Harley Davidson FLSTF / FXDF / FXDLS / FXDWG |
2006 & Older |
1" (double check bar size prior to order!) |
Yes, see notes, According to customer feedback, our 2" pivoting risers will work with stock cables with minor rerouting--our 3" and 4" risers will likely require new cables. |
2" Aluminum
4R-P2RXM |
2" Chrome
4R-P2RX02 |
2" Black
4R-P2RX01 |
- |
| Harley Davidson Heritage Softail |
Up to 2017 |
1" |
Yes, see notes, According to customer feedback, our 2" pivoting risers will work with stock cables with minor rerouting--our 3" and 4" risers will likely require new cables. |
2" Aluminum
4R-P2RXM |
2" Chrome
4R-P2RX02 |
2" Black
4R-P2RX01 |
- |
| Harley Davidson Pan America |
2021-Newer |
1-1/4" |
Yes, see notes, Our 2" bar risers will work great on this bike, with stock cables, with some easy cable rerouting. This process will vary between bikes but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Aluminum
1R-P13RINM |
2" Anodized
1R-P13RIN |
- |
- |
| Harley Davidson XG 500/750 |
All Years |
7/8" |
unknown, Although most bikes can install our 2" risers without replacing the stock cables, we don’t have any record of cable length on this specific bike. If you have information that can help please give us a call at 218.326.1794 |
2" Anodized
3R-P2SSM |
- |
- |
- |
| Honda Africa Twin |
2016 & Newer |
1 1/8" |
Yes, see notes, Our 2" bar risers will work great on this bike with some very minor cable rerouting. First, remove any plastic zip ties holding the cables back. The brake line also has a rubber grommet on it that is running through a metal retainer clip. Push this rubber grommet outside of the metal retainer clip and it will allow the brake line to have the extra slack that it needs to install our risers. Our Gunmetal Gray color risers are the best match for the OEM triple clamp. Always double check all of your cable lengths prior to installing our risers. |
2" Pivoting
1R-P2PP |
1.5" Barback Style
3R-B17R |
- |
- |
| Honda CB 300/500/1000/1100 |
Up to 2018 |
7/8" |
Yes, see notes, According to customer feedback, our 2" risers will work on this bike with some cable rerouting. This process will vary between bikes but it is minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Anti-Vibe SE
1R-AV2SE |
2" Aluminum SE
1R-P2SE |
| Honda CB 300/500/500X |
2019 and Newer |
1 1/8" |
Yes, see notes...., . You do not need to replace any of the cables with the 2 inch risers. You just cut a few zip ties and removed the cables from their runs. Also cut the zip ties for the electrical and throttle. cable re-routing is all that is needed." |
2" Anti-Vibe
1R-AV2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
1.5" Barback Style
3R-B17R |
| Honda CTX 700/1300 |
All Years |
1 1/8" |
Yes, see notes, Our 2" bar risers will work great on this bike. Some customers have reported having to do minor cable rerouting. This process will vary between bikes but it is minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| Honda CRF 150F |
All Years |
7/8" |
Yes, see notes, According to customer feedback, our 2" pivoting risers can be installed using all the stock cables, but cable rerouting will be required. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Anti-Vibe SE
1R-AV2SE |
2" Aluminum SE
1R-P2SE |
| Honda CRF 250, 300, Rally & 450 |
All Years |
7/8" |
Yes, see notes, According to customer feedback, our 2" pivoting risers can be installed using all the stock cables, but cable rerouting will be required. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Anti-Vibe SE
1R-AV2SE |
2" Aluminum SE
1R-P2SE |
| Honda Grom |
All Years |
7/8" |
Yes, see notes, According to customer feedback, our 2" pivoting risers can be installed using all the stock cables, but cable rerouting will be required. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
2" Anti-Vibe SE
1R-AV2SE |
| Honda NC 700/700X |
All Years |
7/8" |
yes |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
2" Anti-Vibe SE
1R-AV2SE |
| Honda Rebel 300, 500 |
All Years |
1" |
Yes, |
1.5" Black
3R-B20R-RBL |
|
|
|
| Honda CL500 Scrambler |
2023 |
7/8" We've been told |
Not Sure, We have not had one of these bikes in our shop. Do you have one and would want to try some of our risers? Send us an email or call us. |
|
|
|
|
| Honda Rebel 1100 |
All Years |
1" |
Most years, , ***The 2025 models may have issues with the brake lines*** Be sure to check before ordering the risers. According to our records, our 2" pivoting risers will work on the 2024 and older bikes without replacing the cables, taller risers will likely require modification to the OEM cables. If you have information that can help please give us a call at 218.326.1794 |
2" Black
Rebel Kit |
1.5" Black
3R-B20R-RBL |
|
|
| Honda Shadow 600 / 750 / 1100 |
All Years |
1" |
Yes, See Notes, According to our records, our 2" pivoting risers will work on this bike without replacing the cables, taller risers will likely require modification to the OEM cables. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
3" Black
P3RX01 |
| Honda ST1100 |
1991-2002 |
7/8" |
Yes, see notes, According to customer feedback the ST1100 can use our 2" pivoting risers without replacing any of the stock cables. Minor cable rerouting may be required. No additional feedback at this time. More questions? You can call us at 218.326.1794 |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Honda VTX 1300 |
All Years |
1" |
Yes, See Notes, According to customer feedback, this bike can use up to 3" tall risers without changing out any of the cables. Simply reroute the cables from any of the OEM retainer clips (or wire looms) that are holding the cables back and you should be good to go. More questions? Just give us a call at 218.326.1794 |
2" Aluminum
P2RXM |
2" Black
P2RX01 |
3" Aluminum
3R-P3CCM |
3" Black
P3RX01 |
| Honda XR150L |
2023 and newer |
7/8" |
yes |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
1 1/4" Aluminum SE
3R-B12POE |
| Honda XR650 L + R |
All Years |
7/8" |
yes |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
2" Anti-Vibe SE
1R-AV2SE |
| Husqvarna Svartpilen 401 |
2020 & Newer |
26mm |
Most of the Time, see notes, According to records, the OEM cables will only allow for a 1-3/4" riser MAX. Our 1-3/4” will work on most KTM 390’s, the cables will barley work with a safe amount of cable length. All customers have reported having to reroute cables and free up cable length. This process will vary between bikes but it is usually not too difficult and can include: cutting zip ties, removing cable from clamp(s) on the lower section of the triple tree / frame, and/or changing how cables run through the top of triple tree. Most customers can get these risers to work great, however due to manufacturing variances of this bike some customers have not been able to get the OEM cables to free up enough length to install the risers safely. |
1 3/4" ANODIZED BLACK
3R-P2PPL390 |
- |
- |
- |
| Indian Chieftain / Roadmaster |
Most |
1 1/4" |
Yes,On Most, **** SOME OF THESE BIKES WILL NOT ALLOW OUR RISERS TO MOUNTS**** Check the Indian Forum and your bike to see if you have the triple clamp that allows our risers to fit!! Our 2" risers for 1 1/4" handlebar will work on the Chieftan / Roadmaster will work with all the stock cables, but the positioning is fairly limited because of the large OEM faring. Visit the link on the 2" riser page for more info and photos. Adding risers to this bike will require rerouting of the cables. Call us at 218.326.1794 for more info. |
2" Black
1R-P13RIN |
- |
- |
- |
| Indian Scout / Scout Bobber |
2024 and Older |
1" |
yes |
2" Black
4R-P2RIN |
- |
- |
- |
| Indian Scout Classic, Scout Bobber, Super Scout |
2025 and Newer |
1" |
yes |
2" Black
4R-P2RIN |
- |
- |
- |
| Indian Scout Sport and Scout 101 |
2025 and Newer |
1" |
yes, this bike uses the caps we provide, on top of our risers. The OEM cap needs to stay in it's original location to clamp the risers to the bike, unlike the earlier model Scout's. You are limited how far back you can rotate the risers because of the speedo location. the cables and lines do work with this riser though. |
2" Black
4R-P2RIN |
- |
- |
- |
| Kawasaki KLR 650 |
All Years |
7/8" |
Yes |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
2" Anti-Vibe SE
1R-AV2SE |
| Kawasaki Versys 300X |
All Years |
7/8" |
Yes, See Notes, According to customer feedback Parts 3R-B12POE and 3R-B12POEK risers are the only ones to work with the OEM cables and lines. Any taller risers will require new cables. More questions? Just give us a call. 218-326-1794 |
1 1/4" Aluminum SE
3R-B12POE |
1 1/4" Black SE
3R-B12POEK |
- |
- |
| Kawasaki Versys 650 |
All Years |
7/8" |
Yes |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
2" Anti-Vibe SE
1R-AV2SE |
| Kawasaki Versys 1000 |
2015 & Newer |
1 1/8" |
Yes, see notes, According to customer feedback our 1.75" risers will work on this bike with the stock cables with some minor rerouting. Customer feedback: I removed the small plastic clip that held the brake line and also removed the entire metal bracket the holds the cable bundle and that gave me the slack I needed to install the risers. More questions? Just give us a call. 218-326-1794 |
1 3/4" Anodized
3R-P2PPL |
1 3/4" Black
3R-P2PPLK |
- |
- |
| Kawasaki Vulcan 900 |
All Years |
1" |
Yes, see notes, According to feedback from customers, the Rox 2" risers should work on the Vulcan 900 with Minor Cable Adjustment/Rerouting. New Cables will likely be required for Rox 3" or 4" risers. Do you have more info that could help? Give us a call: 218-326-1794 |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
3" Black
P3RX01 |
| Kawasaki Vulcan 1700 Vaquero |
2016 & Newer |
1 1/4" |
yes |
2" Black
P13RIN |
- |
- |
- |
| Kawasaki Z650 |
All Years |
NA |
NO, See Notes-ROX Risers will not work because of the speedo location. |
- |
- |
- |
- |
| Kawasaki Eliminator |
2024 |
NA |
Not Sure-Do you have one of these bikes and you're looking for risers? Call us and we can work with you. 218-326-1794. We have not had one in our shop to work on |
- |
- |
- |
- |
| Kawasaki Z800/Z900 |
Up to 2018 |
7/8" |
TBD, see notes, Although most bikes can manage to install our 2" pivoting risers using all the stock cables, we don’t have specific feedback on this bike. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Kawasaki Z1000 |
All Years |
1 1/8" |
Unknown, We don’t have any record of OEM cable length on this bike. Do you have info that can help? Call us at 218-326-1794 or email sales@roxspeedfx.com |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| KTM 250, 300XC, 350EXC/XC/SX, 450EXC/SX/XC, 500EXC/XC |
All Years |
1 1/8" |
yes, see notes, Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
1 3/4" Anodized
3R-P2PPL |
1 3/4" Black
3R-P2PPLK |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
| KTM 390 DUKE / ADV |
2020 & Newer |
26mm |
see notes,, According to our latest records, manufacturing variances of this bike, some customers have not been able to get the OEM cables to free up enough length to install the risers safely. The clutch cable is the main issue, but other cables now also seem to be an issue as well. Be sure to pull your bars off and double check your bike prior to buying the risers. We are hoping to have a new block barback riser done in the coming months that will work with all your OEM cables and lines. |
1 3/4" ANODIZED BLACK
3R-P2PPL390 |
- |
- |
- |
| KTM 690 E + R |
All Years |
1 1/8" |
yes, see notes, Non-ABS models of this bike can use our 2" or 1 3/4" risers. For ABS models we only recommend using our 1 3/4" because of the OEM cable length. Some customers have reported being able to install our 2" risers with minor cable rerouting across all bikes, but this may vary. Installing risers my require cutting zip ties, removing cable clamp(s), and/or changing how cables run through the top of triple tree. Do you have more info that could help? Call us at 218-326-1794. |
1 3/4" Anodized
3R-P2PPL |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| KTM 990/950 Adventure/Adventure Baja/Super Enduro |
All Years |
1 1/8" |
yes, see notes, Our 1 3/4" or 2" bar risers will work great on this bike. Some customers have reported having to do minor cable rerouting. This process will vary between bikes but it is minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
1 3/4" Anodized
3R-P2PPL |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
| KTM 790/890/990/1090/1190/1290 Adventure, Adventure R & Super ADV |
All Years |
1 1/8" |
yes, see notes, According to our records, the OEM cables will only allow for our 1 3/4" riser. Some customers have reported having to do minor cable rerouting. This process will vary between bikes but it is minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
1 3/4" Anodized
3R-P2PPL |
1 3/4" Black
3R-P2PPLK |
- |
- |
| KTM Super Duke 1290 |
All Years |
1 1/8" |
Yes, see notes, According to our records, the OEM cables will only allow for our 1 3/4" riser. Some customers have reported having to do minor cable rerouting. This process will vary between bikes but it is minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
1 3/4" Anodized
3R-P2PPL |
1 3/4" Black
3R-P2PPLK |
- |
- |
| Moto Guzzi V100 S Mandello |
2023 - Newer |
1 1/8" |
Yes, see notes ** According to customer feedback the stock cables are long enough to install these risers without replacing anything. |
1.5" Barback Style
3R-B17R |
- |
- |
- |
| Moto Guzzi Eldorado or California |
2014-2020 |
1 1/8" |
Yes, see notes, According to customer feedback, minor cable rerouting is necessary to use our 2" risers with the stock cables. Removing zip ties / cable clamps is also recommended. We have confirmed "1R-P2PP risers work on the 2016 Moto Guzzi Eldorado" Do you have info that can help? Call us at 218-326-1794 or email sales@roxspeed.com |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
|
| Moto Guzzi Stelvio 1200 |
All Years |
1 1/8" |
Yes, see notes, According to customer feedback, minor cable rerouting is necessary to use our 2" risers with the stock cables. Customers have reported that extra cable length can be found by lifting the gas tank and threading the cables more forward. Removing zip ties / cable clamps is also recommended. The throttle cable is cable tied tight to the frame, so it can be eased off to allow the risers to move fully. Do you have info that can help? Call us at 218-326-1794 or email sales@roxspeedfx.com |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| Moto Guzzi V7 Stone |
2023 |
7/8" |
Yes, see notes,, According to customer feedback, our 2" risers will work on this bike with some cable rerouting. This process will vary between bikes but it is minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
| Royal Enfield Himalayan |
2023 |
7/8" |
Yes, see notes,, According to customer feedback, our 2" risers will work on this bike with some cable rerouting. This process will vary between bikes but it is minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Anti-Vibe SE
1R-AV2SE |
2" Aluminum SE
1R-P2SE |
| Royal Enfield 650 Int. |
All Years |
7/8" |
yes, see notes***, Installing risers on this bike will require minor rerouting of the cables. . Raise tank( 2bolts easy) cut tie wraps for brake line and throttle cables, raise cables above rubber tank attachment. This will provide enough slack.
Remove the neck attached to the forks (3 bolts) , detach brake lever and master cylinder from the handlebar and swing over to the right side of the neck. This will give plenty of slack without the need to remove the banjo bolt and will save the hassle of bleeding the brakes.
Remove left signal to remove clutch cable grommet bracket as this will give plenty of slack. Lastly, inside the headlight there is enough slack on all the wiring.
Then just follow the directions that come with the risers. Total time approximately 30 minutes start to finish.
(s). |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Suzuki M109 Boulevard |
2008 & Newer |
1 1/4" |
Unknown, see notes, Our 2" pivoting risers for bikes with 1 1/4" handlebars will mount on this bike. Although most bikes can install our 2" pivoting risers without replacing the cables, we don’t have record of OEM cable length on this specific bike. Do you have info that can help? Call us at 218.326.1794. |
2" Black
P13RIN |
- |
- |
- |
| Suzuki C50/C90 |
All Years |
1" |
YES, These Bikes can manage to install our 2" pivoting risers using all the stock cables, according to customer feedback. GOing taller than 2 inches may require new cables and lines |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
3" Black
P3RX01 |
| Suzuki DL1000XT V-Strom |
2018 |
1 1/8" |
TBD, see notes, Although most bikes can install our 2" risers without replacing the stock cables, we don’t have any record of cable length on this specific bike. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| Suzuki DL1000XT V-Strom |
2019-Newer |
1 1/8" |
Yes, see notes, According to customer feedback, our 1.25" block offset risers are the only model that will work without replacing the brake/clutch line. For extended brake lines we recommend Spiegler Performance. Phone # 937.291.1735 |
1 1/4" Aluminum SE
3R-B12POE |
- |
- |
- |
| Suzuki DL1000 V-Strom with ABS |
All Years |
7/8" |
see notes, According to customer feedback, our 1.25" block offset risers are the only model that will work without replacing the brake line. For extended brake lines we recommend Spiegler Performance. Phone # 937.291.1735 |
1 1/4" Aluminum SE
3R-B12POE |
- |
- |
- |
| Suzuki DL1000 V-Strom GEN 1 - Non-ABS |
All Years |
7/8" |
yes, see notes, Installing risers on this bike will require minor rerouting of the cables. This process will vary between bikes but it is usually minor and can include: adjusting how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Suzuki DL650 V-Strom with ABS |
All Years |
7/8" |
see notes, According to customer feedback, our 1.25" block offset risers are the only model that will work without replacing the brake line. For extended brake lines we recommend Spiegler Performance. Phone # 937.291.1735 |
1 1/4" Aluminum SE
3R-B12POE |
- |
- |
- |
| Suzuki DL650 V-Strom GEN 1 - Non-ABS |
All Years |
7/8" |
see notes, According to customer feedback NON ABS models of the Vstrom 650 can install our 2" pivoting risers without replacing cables. Cable rerouting will be required. This process will vary between bikes but it is usually minor and can include: adjusting how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
1 1/4" Aluminum SE
3R-B12POE |
- |
| Suzuki DR650 |
All Years |
7/8" |
yes |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Suzuki DRZ 400/650 |
All Years |
7/8" |
yes |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Anti-Vibe SE
1R-AV2SE |
2" Aluminum SE
1R-P2SE |
| Triumph Scrambler |
2016 & Older |
7/8" |
Yes, see notes, According to customer feedback the stock cables are long enough to accomodate our 2" risers with some minor rerouting. This can include: adjusting how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Anti-Vibe SE
1R-AV2SE |
2" Aluminum SE
1R-P2SE |
| Triumph Scrambler |
2017 & Newer |
1 1/8" |
Yes, see notes, According to customer feedback the stock cables are long enough to accomodate our 2" risers with some minor rerouting. This can include: adjusting how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s). |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Triumph Speed Triple |
2007 & Older |
7/8" |
yes, see notes, Installing risers on this bike will likely minor require rerouting of the cables. This process will vary between bikes but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Anti-Vibe SE
1R-AV2SE |
2" Aluminum SE
1R-P2SE |
| Triumph Speed/Street Triple |
2008 & Newer |
1 1/8" |
yes, see notes, Installing risers on this bike will likely minor require rerouting of the cables. This process will vary between bikes but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Triumph Street Twin |
2016 & Newer |
7/8" |
YES, Installing risers on this bike will require rerouting of the cables. This process will vary between bikes but it is usually minor and can include: adjusting how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) |
2" Anodized
3R-P2SSM |
- |
- |
- |
| Triumph Bonneville T120 |
All Years |
1" |
Unknown, Most bikes can manage to install our 2" pivoting risers using all the stock cables, but we don’t have specific feedback on this bike. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
- |
| Triumph Thruxton |
2014 - Older |
1" |
Unknown, Most bikes can manage to install our 2" pivoting risers using all the stock cables, but we don’t have specific feedback on this bike. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
3" Black
P3RX01 |
| Triumph Thunderbird |
2009 & Newer |
1 1/4" |
NO, We do not have a riser that works with on Bikes that have a one piece cap and a 1.25” diameter handlebars. These bikes require our risers to have a longer bottom post which we do not have currently. Thunderbirds with a 1 inch diameter bar, our risers may work. We have not had one of them in our shop to confirm though. Any questions give us a call at 218.326.1794 |
|
|
|
|
| Triumph Tiger 800 XC/XCS |
2011 & Newer |
1 1/8" |
Yes, see notes** ROX Block Risers will NOT work on any Tiger** The Pivoting risers we list to the right WILL fit. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| Triumph Tiger 800 Street/Roadie |
2011 & Newer |
1 1/8" |
Yes, see notes** ROX Block Risers will NOT work on any Tiger** The Pivoting risers we list to the right WILL fit |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Triumph Tiger 900/1050 |
1993-2012 |
7/8" |
Yes, see notes** ROX Block Risers will NOT work on any Tiger** The Pivoting risers we list to the right WILL fit |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Triumph Tiger 900 / Tiger 900 Rally Pro |
2020-Newer |
1 1/8" |
Yes, see notes** ROX Block Risers Will not work on any Tiger** The Pivoting risers we list to the right WILL fit. All of the stock cables will work with minor rerouting. This can include: removing zip ties, moving the cables outside of cable clamps, and/or adjusting how cables run around the triple tree. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Anti-Vibe
1R-AV2PP |
| Triumph Tiger 1200 Explorer |
2012-2015 |
1 1/8" |
yes, see notes** ROX Block Risers Will not work on any Tiger** The Pivoting risers we list to the right WILL fit. Installing risers on this bike will likely minor require rerouting of the cables. This process will vary between bikes but it can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Triumph Trident 660 |
2021 - Newer |
1 1/8" |
Yes, see notes ** According to customer feedback the stock cables are long enough to install these risers without replacing anything, but removing the rubber cable ties is necessary. Changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. Be sure to double check cable length prior to purchasing risers. |
1.5" Barback Style
3R-B17R |
- |
- |
- |
| Triumph Tiger 1200 |
2016 and Newer |
1 1/8" |
No, See Notes** ROX Block Risers Will not work on any Tiger** According to customer feedback, the stock clutch cable and throttle cable doesn’t work with our riser. ROX Riser will fit with cable extensions. |
- |
- |
- |
- |
| Victory V92C |
All Years |
1" |
yes, see notes** Rox 2" Risers will work on the V92C with Very Minor Cable Adjustment. New Cables will likely be required for Rox 3" or 4" risers. Have more info that could help? Give us a call: 218-326-1794 |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
3" Black
P3RX01 |
| Yamaha Bolt |
All Years |
1" |
yes, see notes**Our 2" pivoting risers will work on the Bolt with all the stock cables, but the OEM speedo assembly will limit the options for positioning. Rox 3" or 4" risers will mount on the Bolt as well but would likely require all new cables. As with any bike, remove any zip ties or cable clamps that might be restraining the cables. Minor cable rerouting may be necessary. Please double check your cables before riding. More questions? Just call us at 218-326-1794 |
2" Black
P2RX01 |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
- |
| Yamaha FJ09 |
All Years |
1 1/8" |
yes, see notes**According to Customer Feedback: Your 2" pivoting risers do indeed fit the bike, but it is a very tight fit. Remove the frame loop that is holding the brake line back and any zip ties. You do not need to replace the clutch cable, you can just reroute it at the back of the front fork instead of in the front of the fork like it is originally. You also need to adjust the throttle cable with the adjustment nut that's on it, if not when the handlebars are turned to the right at the maximum, the throttle is hard to turn and does not return quickly, or at all, which can be dangerous. Also, all the zip ties that hold the electrical wires have to be cut. With an hour's worth of work, the result is very good and the comfort greatly improved. Cable length can vary slightly between bikes, so please check your cables prior to ordering risers. More questions? Just call us at 218-326-1794 |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Yamaha FZ1 |
All Years |
7/8" |
unknown, Most bikes can manage to install our 2" pivoting risers using all the stock cables, but we don’t have specific feedback on this bike. If you have information that can help please give us a call at 218.326.1794 |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Yamaha FZ6 |
All Years |
7/8" |
see notes, 2009 and older years of this bike include a 1 piece cap for the top of the OEM handlebar. Bikes that include this 1 piece top cap will need to buy our Rox Steel Replacement caps to use in place of the 1 piece Yamaha OEM cap. Installing risers on this bike may require rerouting of the cables. This process will vary between bikes but it is usually minor and can include: cutting zip ties, removing cable clamp(s) on the lower section of the triple tree, and/or changing how cables run through the top of triple tree. |
2" Aluminum SE
1R-P2SE |
2" Black SE
1R-P2SEK |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
| Yamaha FZ8 |
All Years |
7/8" |
unknown, see notes, We have heard mixed signals in regard to whether the OEM cables are long enough to install our 2" pivoting risers. Our shorter 1 1/4" offset block risers will likely work without any issue. If you have information that can help please call us at 218-326-1794 or email sales[at]roxspeedfx.com |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
1 1/4" Aluminum SE
3R-B12POE |
1 1/4" Black SE
3R-B12POEK |
| Yamaha FZ07 |
All Years |
*See notes |
No, see notes, According to feedback we have received, Rox Risers will not work on the FZ07 because the OEM Speedo Cluster interferes and will not allow any of our bar risers to mount properly. We don’t currently have any options for handlebar risers on this bike. Do you have other info that can help? Know a way around it? Please call us at 218-326-1794. |
*See notes |
|
|
|
| Yamaha FZ09 / FZ10 |
All Years |
1 1/8" |
unknown,Most bikes can manage to install our 2" pivoting risers using all the stock cables, but we don’t have specific feedback on this bike. If you have information that can help please give us a call at 218.326.1794 |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Yamaha Vmax |
All Years |
1 1/8" |
Yes, see notes, According to customer feedback our 2" risers will work with all the stock cables. Minor cable rerouting may be required. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Yamaha Super Tenere |
2013 & Older |
1 1/8" |
Yes, see notes, Installing risers on this bike will require rerouting of the cables. This process will vary but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum
1R-P2PP |
2" Anodized
1R-P2PPA |
2" Black
1R-P2PPK |
2" Gunmetal
1R-P2PPG |
| Yamaha Super Tenere |
2014 & Newer |
1 1/8" |
yes, see notes, Installing risers on this bike may require rerouting of the cables. This process will vary but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
| Yamaha Tenere 700 |
2021-2024 |
1 1/8" |
Yes, see notes, Front brake Hydraulic hose/line is held with a plastic retainer on the frame and needs to be removed. Right Electrical runs appear to be fine but they could be slide up giving even more slack. Clutch cable is where the issues will be. The cable just starts to get snug if you don’t move it down by the crank case and frame. Actually, it’s snug either way. I bumped the clutch lever mount in about 3/16”. Left electrical lines are fine. 3R-B12POE and 3R-B17R-15M Risers are no problems but front brake hose should still be set free. |
1 1/2" Barback Risers
3R-B17R-15M |
1 1/4" Aluminum SE
3R-B12POE |
2" Black
1R-P2PPK |
2" Anodized
1R-P2PPA |
| Yamaha TW200 |
Alll Years |
7/8" |
yes, see notes, Installing risers on this bike will require rerouting of the cables. This process will vary but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Aluminum
1R-P2SSN |
2" Black
1R-P2SS |
2" Aluminum SE
1R-P2SE |
2" Anti-Vibe SE
1R-AV2SE |
| Yamaha V-Star 650 / 950 / 1100 |
All Years |
1" |
yes, see notes, Rox Risers will work on the V-Star 250, 650, 950, and 1100. According to our records the OEM cables should allow for 2" risers without any problems. Minor rerouting, cutting zip ties, or removing cable clamps may be necessary. The only Rox Risers that will work on the Vstar 1300 are our 4" pivoting risers because the OEM Speedo interferes with our shorter risers, but installing our 4" risers on the Vstar 1300 will require extending all of the cables and lines. The Vstar 250 has a 7/8" handlebar, but our 2" pivoting risers for 7/8" bar should work (see the listing for Yamaha FZ8). |
2" Aluminum
P2RXM |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
3" Black
P3RX01 |
| Yamaha Venture |
2018 |
1" |
yes, see notes, Rox 2" Risers will work on the 2018 Yamaha Venture with no cable changes however. According to our records the OEM cables will allow for 2" risers without any problems. Minor rerouting, cutting zip ties, or removing cable clamps may be necessary. |
2" Chrome
P2RX02 |
2" Black
P2RX01 |
2" Aluminum
P2RXM |
2" Black
4R-P2CC01 |
| Yamaha XSR 900 |
2016 & Newer |
1 1/8" |
yes, see notes, Installing risers on this bike may require rerouting of the cables. This process will vary but it is usually minor and can include: changing how cables run through the top of triple tree, cutting zip ties, and/or removing cable clamp(s) on the lower section of the triple tree. |
2" Anodized
1R-P2PPS10A |
2" Black
1R-P2PPS10K |
- |
- |
